How to fix Huawei BM622m firmware, No Signal Lights , Ready Only, and Continues LAN Refresh
How to fix Huawei BM622m No Signal Lights , Ready Only, and Continues LAN Refresh.
This happen when you upgrade it to GreenPacket firmware or done by wrong flashing or command.
In my case I accidentally flash it to GreenPacket via winspreader I suppose to flash a DV235t.
Then I want it back to 622m firmware and this what happen
This are the fallowing errors that can be corrected:
Other find a solution use Winpsreader every time you want to connect ( hustle sign)
Read Also: How To Use Winspreader v0.07
How to Fix Restore your modem settings
NOTE: Don not use this for factory /etc/default.cfg this can cause hardware issue
while rebooting you will notice that you have led light
This happen when you upgrade it to GreenPacket firmware or done by wrong flashing or command.
In my case I accidentally flash it to GreenPacket via winspreader I suppose to flash a DV235t.
Then I want it back to 622m firmware and this what happen
This are the fallowing errors that can be corrected:
- How To Fix Tulala LED BM622, BM622m, BM622i?
- No signal Lights
- My LAN continues Refresh connected disconnected if 622m firmware while on Greenpacket firmware LAN is normally connected.
- 622m web GUI status Ready
- Possible solution for 169 IP
- Unidentified Network
Other find a solution use Winpsreader every time you want to connect ( hustle sign)
Read Also: How To Use Winspreader v0.07
How to Fix Restore your modem settings
Continues LAN and Ready on Status (Normally this must be connecting not Ready)
1. Get a Winspreader and Smart v7 firmware
2. Open a Winspreader browse the Smart v7 firmware Hit start.
3. Plug your Modem Power and Lan Cable the wait a few minutes....
4. check the web GUI .. type the 192.168.254.1 on your browser
5. If you Gui Change to Smart...
Open telnet 192.168.254.1
login: mt7109
password:wimax
sncfg dset ADMIN_NAME admin (Enter)
sncfg dset ADMIN_PASSWD '$1$k2I9hJe4$OkHKF43oTmjvv3zJtrEZ4.' (Enter)
sncfg commit (Enter)
/factoryreset.sh (Enter)
6. After Reboot your default gateway should be 192.168.15.1 because that is the default IP for smart.
Open a browser type 192.168.15.1
log in user :admin pass:smart
7. Go to Management -->> Upgrade --->> browse your 622m firmware Hit upgrade
wait 10 to 15 minutes slowly but surely effective flashing...
8. After done Upgrade it will reboot hit that reboot and wait...
9. reboot done check ip still 192.168.15.1 (smart)
Open a browser type 192.168.15.1 then you will see PINK page with error link is like this http://192.168.15.1/publicinfo.html
Now open a telnet again
Telnet 192.168.15.1
Login:Firefly
Pass:$P4mb1h1r4N4m4nT0!!
/factoryreset.sh (enter)
NOTE: Don not use this for factory /etc/default.cfg this can cause hardware issue
10. Now after factory reset automatically you can't login to telnet. Log in to GUI first
username: user
password: 0SlO051O
Go to http://192.168.254.1/advanced/acl.html to enable telnet access.....
CHECK TELNET and click apply...
11. Finally No signal Light
Now open a telnet again
Telnet 192.168.15.1
Login:Firefly
Pass:$P4mb1h1r4N4m4nT0!!
rm etc/default.cfg ( Enter )
reboot (Enter)
while rebooting you will notice that you have led light
Comments
Post a Comment